SWG Packet Encryption
SWG uses a XOR Mask encryption based off the value of the CRCSeed exhanged in the Session Reply packet. All the data between the SOE Opcode and CRC value are encrypted. If the packet does not contain any SOE Protocol, it is encrypted between the 1st byte and the CRC value. XOR is a simple bitwise operation on 2 numbers, know as an exclusive-or, when ONLY 1 bit is 1, results in a 1. This is it's truth table.
A B C 0 0 0 0 1 1 1 0 1 1 1 0
For more information on the XOR operator, use Google.
Here are code samples of the Encrypt() and Decrypt() functions.
//PROTOTYPES
void Decrypt(char *pData,unsigned short nLength, unsigned int nCrcSeed);
void Encrypt(char *pData,unsigned short nLength,unsigned int nCRCSeed);
//DECRYPT
void Decrypt(char *pData,unsigned short nLength,unsigned int nCrcSeed)
{
nLength-=4;
unsigned int *Data = (unsigned int*)(pData+2);
short block_count = (nLength / 4);
short byte_count = (nLength % 4);
unsigned int itemp;
for(short count = 0;count<block_count;count++)
{
itemp = *Data;
*Data ^= nCrcSeed;
nCrcSeed = itemp;
Data++;
}
pData = (char*)Data;
for(short count = 0;count<byte_count;count++)
{
*pData ^= nCrcSeed;
pData++;
}
}
//ENCRYPT
void Encrypt(char *pData, unsigned short nLength,unsigned int nCrcSeed)
{
nLength-=4;
unsigned int *Data = (unsigned int*)(pData+2);
short block_count = (nLength / 4);
short byte_count = (nLength % 4);
unsigned int itemp;
for(short count = 0;count<block_count;count++)
{
*Data ^= nCrcSeed;
nCrcSeed = *Data;
Data++;
}
pData = (char*)Data;
for(short count = 0;count<byte_count;count++)
{
*pData ^= (char)nCrcSeed;
pData++;
}
}
Encryption Explained:
It begins by adjusting the pointer and data length to exclude the SOE Opcode and CRC Value at the beginning and end of the packet. Then the number of "blocks" or 4 byte chunks of data are calculated. Then a remainder of bytes are calculated. The algorithm uses a for loop to go through each chunk, and then each remaining byte of the packet to encrypt/decrypt. The algorithm stats off by using the CRCSeed as the first mask value to do the XOR operation against. For encryption, the resulted data is then set as the new mask. For decryption, the original data is copied, then the XOR operation occures, and the copy of the encrypted data is set as the new mask. This recurses for EACH "block" of data. When it gets down to the remainder, the first byte of the last mask is XOR'd against each individual remaining byte until the process becomes completed.
The following is a step by step example on an arbitrarily made-up packet.
00 09 00 01 00 02 AB 43 E3 D5 00 FF 00 11 45 32 76 43 D4 F1 00 AB CD First we know the first 2 bytes are the SOE opcode 0x09 (data on channel 00) So we ignore this as we need it to identify the packet. We also ignore the last two because it is for the CRC value. The remainder is what needs to be encrypted (or decrypted in another case). Say our Key is '''(1D 4E 32 87)''' this will also act as our first mask. So, taking the first 4 bytes after the SOE opcode '''(00 01 00 02)''' 00 01 00 02 XOR 1D 4E 32 87 ------------- 1D 4F 32 85 So the beginning of the new packet is '''00 09 1D 4F 32 85'''. Now we take the result as our new mask and xor the next 4 bytes AB 43 E3 D5 XOR 1D 4F 32 85 ------------- B6 0C D1 50 New packet so far: 00 09 1D 4F 32 85 B6 0C D1 50 New mask: B6 0C D1 50 00 FF 00 11 XOR B6 0C D1 50 ------------ B6 F3 D1 41 New packet so far: 00 09 1D 4F 32 85 B6 0C D1 50 B6 F3 D1 41 New mask: B6 F3 D1 41 45 32 76 43 XOR B6 F3 D1 41 ------------- F3 C1 A7 02 New packet so far: 00 09 1D 4F 32 85 B6 0C D1 50 B6 F3 D1 41 F3 C1 A7 02 New mask: F3 C1 A7 02 Now that we are out of full 4 byte blocks, we xor each last byte with the first byte in our “key” D4 F1 00 XOR This is done in a separate loop, and per byte, so D4 xor F3, then F1 F3 F3 F3 xor F3, then 0E xor F3. And the results are all appended to our packet --------- 27 02 F3 Final Encrypted Packet: 00 09 1D 4F 32 85 B6 0C D1 50 B6 F3 D1 41 F3 C1 A7 02 27 02 F3 AB CD
Decryption would be the reverse of the encryption process. Encryption is applied AFTER Compression, but BEFORE a CRC value is appended.
VERY IMPORTANT NOTE:
After the discovery of stand-alone SWG Packets (Outside of SOE protocol), the encryption and decryption algorithms have a slight difference in how they adjust for the CRC/SOE opcode. Stand alone SWG Packets are encrypted between the first byte and the CRC value. SOE protocol'd packets are encrypted between the SOE Opcode(2nd byte) and the CRC value. The actual code should account for this however the explaination will not.
